Use the Hawk Scraper to remove tile adhesives, carpet backing, industrial grease & soil, and coatings from hard surfaces. 13”,
17”, and 20” sizes. The Scraper drives six 1”x1” carbide steel blades, each on a dual-position rigid mount. Drive the Scraper with
a Hawk Severe Duty Floor Machine with a 1.5 HP motor.
Engineered Design
• Two sizes – 13″ and 20″. The 20″
Scraper fits 17″ and 20″
machines
• 3/8” thick steel plate construction. The plate is e-coated for
corrosion resistance.
• The plate is fit with six (6) tungsten steel cutter holders mounted
with easily removed, allen head screws
• Each cutter holder carries one (1) 1” x 1” carbide cutting blade.
Each blade has 8 cutting edges.
• Mount the blade for a wide cutting edge, or a sharp cutting point
• The Hawk Scraper
mounts on the floor machine with a custom
milled aluminum clutch plate on a riser (included).
The Hawk CLAW Diamond Pad Driver provides peak grinding and polishing results to the natural stone and concrete tradesman. The CLAW
is available in five sizes – 10”, 13”, 15”, 17”, and 20”, driving both 3” round, and trapezoidal tools.Tools are held in milled recesses
in the CLAW plate with the unique Mag-Lok industrial magnet system. Grinding and polishing tools mount securely on the plate, yet
are easy to change without shop tools.
Operating vibrations are reduced by Neoprene rubber vibration damping isolators built into
the mounting system with custom milled aluminum clutch plate. Power the CLAW with your severe-duty 1.5 HP rotary floor machines.
Engineered
Design:
• The weighted CLAW plate is built with 3/8” plate steel, e-coated
for corrosion resistance
and easier clean up
• The face of the CLAW plate is milled with round and trapezoidal
tool mounting recesses,
fit with a Mag-Lok industrial magnet
• The top of the plate is fit with a custom milled aluminum NP9200
clutch
plate, sitting on top of six 1” Neoprene rubber vibration
isolaters. These isolaters reduce vibration and flex
over high
points and lippage.
• Round 3” resin tools mount securely on a 3” metal adaptor plate
with hook and loop face. The adaptor and tool combination
mounts onto the CLAW plate with the Mag-Lok System.
•
The 17” and 20” CLAW plates add hand grab holes
• Includes round and trapezoidal hole blanks. Blanks prevent
debris buildup in recesses.
• Includes 3” steel mounting adapters with hook & loop mounting
• Order additional adapters(#KIT2018-1 – Set of 6), or the
replacement hook face sheet that mounts on the steel adapters
(#KIT2018 – Set of 6).
The Hawk Orbitec Planetary Driver makes quick work of polishing large concrete and stone areas. Six independent sealed ball bearing pedestals spin 3” tools up to 400 RPM. Orbitec extends tool life through cool running. The Orbitec with counter-rotating heads work 60% faster than fixed tool drivers.
Engineered Design • The Orbitec Driver mounts under most conventional design 1.5 HP / 175 RPM floor machines • The aluminum clutch plate is custom milled to provide easy on and off mounting • Three sizes for use on 13”, 17” and 20” floor machines • The electroplated 1/2” thick steel drive plate is built with six tool-holding pedestal heads • These pedestals with are built with tool holding hook facing, securely mounting round diamond tools with hook-and-loop backing. Diamond tools are quickly changed without shop tools. • The floor machine drives the Orbitec plate at 175 RPM in a clockwise direction. The pedestals spin 3” diamond tools at 400 RPM in a counter clockwise direction. This counter- rotating operation drives diamond tools 60% faster than fixed mount drivers.
• Add the optional dust ring and vacuum hose mounting kits to your Hawk floor machine for dust containment • Add optional machine weights on your Hawk floor machine for greater down pressure and faster floor prep results • Order diamond tools separately
The Hawk Flight Applicator glides across the floor as it applies water-based and solvent-based finishes, restorers and disinfectants in a smooth, even, crystal-clear coat.
Available with 3 aluminum applicator head sizes – 28”, 36” and 48” wide – delivering solutions to the floor at up to 27,500 square feet per hour. The patented, variable-flow control pump can reduce finish usage by up to 20%.
No spills, no drips, no baseboard splashes. Even novice users can perform like a pro.
Engineered Design • 12 V battery-powered 70 psi solution pump delivers finishes to the floor through a 28”, 36” or 48” aluminum applicator bar
• Patented variable flow control switch and a master on/off switch is at your finger tips
• 8” wheels with a magnetic sensor activates the pump as you pull the Flight Applicator across the floor
• Use a lambs wool applicator with added 3” synthetic yarn pad to spread solvent-based finishes
• Use a microfiber applicator pad to apply water-based finishes. (Check the finish product label for the recommended pad type.)
• Pads easily mount to the applicator bar with harpoon hooks
• The corrosion-resistant, powder coated frame is 21” wide x 33.5” deep and holds up to (2) 5 gallon bottles
• A pin-locked handle fits the user’s height, adjusting from 32” to 40” high
• Easy to rinse and clean. Applicator bar and pad disconnects for convenient storage.
The Twin Talon was born out of the need for affordable polishing edger with compact power. Dual 1/8 HP motors spin heads at 500 RPM in opposing directions. The result is very controllable polisher with low center of gravity.
The Twin Talon is small enough to work on counter tops but large enough to polish a small bathroom floor. Available in three sizes. The 36” removable handle (oponal) mounts over the hand grips and lets you stand while using the Twin Talon as an edger, carpet spotter and a floor scrubber.
Engineered Design: • Compact 22.5 lbs. design. 3 sizes (12”, 14”, & 16”)
• The 14” model is designed for use with diamond tools, mounted with pad driver (#AS003-7)
• 1/8 HP dual motors
• Optional 36” easy-mount handle for use while standing
• Exclusive Mag-LockTM brush and driver attaching system
• Durable resin cover over steel frame for reliable performance
• Quiet belt drive power
• Simple operator switch for both hand or foot operation
• 2-piece commercial, 35 ft. (14-3) SJT easy-wrap power cord
• Optional easy-mount handle (#KIT3062)
• Wide selection of drivers & specialty brushes
• UL / CUL approved components for safe performance
The Talon Edger Floor Machine is designed to scrub built-up dirt in corners and on baseboards without bending and back-breaking effort. Scrub with pads or with optional bonnets or brushes. Includes the pad driver and an assorted pad startup kit.
Power
• 1/8 HP, DC motor. 115V, 50/60 Hz power.
• 50 ft. 16-3 SJT detachable power cord
Drive System
• Enclosed, durable gear belt drives brushes and pads at 500 RPM
Engineered Design
• 2 sizes – 6” and 8”
• Handle height adjusts from 47” to 52” with locking pin
• Rotational molded polyethylene housing
• The metal handle collapses over for easy transport and storage
• The brush drive is injection molded, reinforced resin with the unique Mag-Lok™ magnetic system to securely mount brushes and pad drivers without tools
• Optional bristle brushes, pads and bonnets driver
Safety Features
• Quiet operation
• Built with UL approved components
Select the fields to be shown. Others will be hidden. Drag and drop to rearrange the order.
Image
SKU
Rating
Price
Stock
Availability
Add to cart
Description
Content
Weight
Dimensions
Additional information
Click outside to hide the comparison bar
Compare
Volume Pricing
Why should you purchase your janitorial supplies from CILYMI? With so many websites offering cleaning products, here are the reasons why you should consider CILYMI for your bulk cleaning product purchases.
SAVINGS– Simply put, the more you buy, the more you save. Larger orders can contribute to substantial savings by limiting packaging and transportation costs.
RELATIONSHIP PRICING – clients who purchase equipment from CILYMI realize the greatest discounts on consumable items.
VARIETY – we can source thousands of top-quality products
CUSTOMER SERVICE – We partner with purchasing agents, school districts, governmental agencies and other large-scale buyers.
SOURCING – We will work hard to locate and supply a multitude of industry-best janitorial products at the most competitive prices possible.
KNOWLEDGE – We seek to learn about your specific product needs and, when requested, recommend a suitable alternative product when the primary product is unavailable and or not cost-effective